Enhander
FEAR
Administrator
General
Repuation: +36/-0
 Offline
Posts: 8,469
3 Piece and a Biscuit!
|
 |
« on: July 17, 2008, 11:08:11 PM » |
|
Ok, so Ive ran into a few problems fixing my G36 Ion. It had one leak from a large banjo fitting. Replaced the banjo..the leak stopped..and started another spot, my solinoid. So that means the board is shot. I replace the board..and another leak. This one seems minor I hope. Its one of the O-rings in the firing can. So it looks like i get to figure out how the heck to get those O-rings out...and back in.
Also looks like another purchase from big pun...*sigh* Dunno if this thing will be ready for Halo at this point.
Does anyone have spare Ion O-rings?
|
|
|
|
|
Logged
|
|
|
|
sun-tzu
Team F.E.A.R. Member
General
Repuation: +10/-0
Offline
Posts: 1,574
You are DEAD to me!
|
|
« Reply #1 on: July 17, 2008, 11:54:27 PM » |
|
this is a bummer....keep working it....cant wait to see it...no Ion o-rings here
|
|
|
|
|
Logged
|
|
|
|
Enhander
FEAR
Administrator
General
Repuation: +36/-0
Offline
Posts: 8,469
3 Piece and a Biscuit!
|
|
« Reply #2 on: July 18, 2008, 12:07:15 AM » |
|
Yes...i thought Id have it done by now..im highly upset. Now I gotta spend another 35 buckd for o-rings..and detents
|
|
|
|
|
Logged
|
|
|
|
Enhander
FEAR
Administrator
General
Repuation: +36/-0
Offline
Posts: 8,469
3 Piece and a Biscuit!
|
|
« Reply #3 on: July 18, 2008, 12:40:52 AM » |
|
Looks as though there might be a light at the end of the tunnel. It might have just needed greased. I just did that and the leak stopped, but the leak from the QEV presists...new diganosis..bad qev...much easier to replace
PS, The gun will hold air now..with teh stock 1/8th banjo. So now I need a QEV and air..This sucks..no air to test..blah!
|
|
|
|
|
Logged
|
|
|
|
Foxxy
Team F.E.A.R. Member
General
Repuation: +18/-0
Offline
Posts: 2,881
. . . . .
|
|
« Reply #4 on: July 18, 2008, 03:12:09 AM » |
|
I'd let you use my air but I dont have enough. Only like 400-500 psi.Very very low. I have some O-Rings for the ion when I bought off of you if you need still.
|
|
|
|
|
Logged
|
|
|
|
Varnel
Team F.E.A.R. Co-Captain
Global Moderator
General
Repuation: +28/-0
Offline
Posts: 6,026
|
|
« Reply #5 on: July 18, 2008, 02:29:57 PM » |
|
Did you put t-tape one the QEV when you installed it? If I remember right you have the clippard one not the 360 QEV which I had nothing but trouble with mine when I had it. Try some t-tape and when you screw it on don't force it on to tight. when it starts to get tight when putting it on finish the turn and stop. I know when I had mine when I put it as far as it would go in it would leak, but if I left it out a little it was fine and the tape held it in place.
|
|
|
|
|
Logged
|
|
|
|
Enhander
FEAR
Administrator
General
Repuation: +36/-0
Offline
Posts: 8,469
3 Piece and a Biscuit!
|
|
« Reply #6 on: July 18, 2008, 03:43:15 PM » |
|
Mines got a 360 qev..which needs a new o-ring...i think
|
|
|
|
|
Logged
|
|
|
|
Varnel
Team F.E.A.R. Co-Captain
Global Moderator
General
Repuation: +28/-0
Offline
Posts: 6,026
|
|
« Reply #7 on: July 18, 2008, 05:16:38 PM » |
|
Or it could just use some lube on the oring it has now. Also try flipping the oring over. That sometimes helps.
|
|
|
|
|
Logged
|
|
|
|
sun-tzu
Team F.E.A.R. Member
General
Repuation: +10/-0
Offline
Posts: 1,574
You are DEAD to me!
|
|
« Reply #8 on: July 18, 2008, 06:39:54 PM » |
|
have you tried just asking it nicely to stop leaking?  ? |
|
|
|
|
Logged
|
|
|
|
Varnel
Team F.E.A.R. Co-Captain
Global Moderator
General
Repuation: +28/-0
Offline
Posts: 6,026
|
|
« Reply #9 on: July 18, 2008, 09:14:27 PM » |
|
have you tried just asking it nicely to stop leaking? ? Good call! Try that JJ! |
|
|
|
|
Logged
|
|
|
|
|
BLACK MAMBA
Guest
|
|
« Reply #10 on: July 28, 2008, 08:36:47 PM » |
|
i think i have a whole ion repair kit, let me check like wednesday night
|
|
|
|
|
Logged
|
|
|
|
Enhander
FEAR
Administrator
General
Repuation: +36/-0
Offline
Posts: 8,469
3 Piece and a Biscuit!
|
|
« Reply #11 on: August 05, 2008, 05:55:11 PM » |
|
|
|
|
|
|
Logged
|
|
|
|
Varnel
Team F.E.A.R. Co-Captain
Global Moderator
General
Repuation: +28/-0
Offline
Posts: 6,026
|
|
« Reply #12 on: August 05, 2008, 06:32:01 PM » |
|
That gun really impressed me when we were doing that video.
|
|
|
|
|
Logged
|
|
|
|
Foxxy
Team F.E.A.R. Member
General
Repuation: +18/-0
Offline
Posts: 2,881
. . . . .
|
|
« Reply #13 on: August 05, 2008, 08:57:11 PM » |
|
Thats pretty awesome! Taking it to Halo? I know in the vid you said its not quite ready for a game yet.
|
|
|
|
|
Logged
|
|
|
|
|
